Monographs: Pharmaceutical substances: Ethambutol hydrochloride (Ethambutoli hydrochloridum)

Molecular formula. C10H24N2O2,2HCl

Relative molecular mass. 277.2

Graphic formula.

Chemical name. (+)-(S,S)-2,2'-(Ethylenediimino)di-1-butanol dihydrochloride; [S-(R*,R*)]-2,2'-(1,2-ethanediyldiimino)bis[1-butanol] dihydrochloride; CAS Reg. No. 1070-11-7.

Description. A white, crystalline powder; odourless.

Solubility. Soluble in 1 part of water; soluble in ethanol (~750 g/l) TS; practically insoluble in ether R.

Category. Antibacterial (tuberculostatic).

Storage. Ethambutol hydrochloride should be kept in a well-closed container.

Requirements

Definition. Ethambutol hydrochloride contains not less than 98.0% and not more than 100.5% of C10H24N2O2,2HCl, calculated with reference to the dried substance.

Identity tests

• Either tests A and C or tests B, C and D may be applied.

A. Carry out the examination as described under 1.7 Spectrophotometry in the infrared region. The infrared absorption spectrum is concordant with the spectrum obtained from ethambutol hydrochloride RS or with the reference spectrum of ethambutol hydrochloride.

B. See the test described below under "2(R-Aminobutanol)". The principal spot obtained with solution B corresponds in position, appearance, and intensity with that obtained with solution C.

C. A 0.1 g/mL solution yields reaction B described under 2.1 General identification tests as characteristic of chlorides.

D. Melting temperature, about 200°C.

Specific optical rotation. Use a 0.10 g/mL solution; = +5.0° to +7.0°.

Heavy metals. Use 1.0 g for the preparation Of the test solution as described under 2.2.3 Limit test for heavy metals, Procedure 3; determine the heavy metals content according to Method A; not more than 20 μg/g.

Sulfated ash. Not more than 2.0 mg/g.

Loss on drying. Dry to constant weight at 105°C; it loses not more than 5.0 mg/g.

pH value. pH of a 0.01 g/mL solution, 3.0-4.5.

2(R-Aminobutanol). Carry out the test as described under 1.14.1 Chromatography, Thin-layer chromatography, using silica gel R1 as the coating substance and a mixture of 11 volumes of ethyl acetate R, 7 volumes of glacial acetic acid R, 1 volume of hydrochloric acid (~420 g/l) TS, and 1 volume of water as the mobile phase. Apply separately to the plate 2 μl of each of 3 solutions in methanol R containing (A) 50 mg of the test substance per mL, (B) 0.50 mg of the test substance per mL, and (C) 0.50 mg of 2-aminobutanol R per mL. After removing the plate from the chromatographic chamber, allow it to dry in air, heat at 105°C for 5 minutes, cool, spray with triketohydrindene/cadmium TS, heat at 90°C for 5 minutes, and examine the chromatogram in daylight. The spot obtained with solution C is more intense than any spot, corresponding in position and appearance, obtained with solution A.

Assay. Dissolve 0.200 g in 50 mL of water R and add 1.0 mL of hydrochloric acid (0.1 mol/L) VS. Carry out a potentiometric titration using sodium hydroxide (0.1 mol/L) VS. Read the volume added between the two points of inflexion.

1 mL of sodium hydroxide (0.1 mol/L) VS is equivalent to 27.72 mg of C10H24N2O2,2HCl.

to previous sectionto next section